Genel bilgiler
product brand nameSIPLUS
product type designationDC UPS
type of current supplyDC UPS 24 V/40 A
manufacturer's article number of the basic version used for SIPLUS product versions6EP1931-2FC21
input
voltage curve at inputDC
supply voltage at DC rated value24 V
input voltage at DC22... 29 V
adjustable response value voltage for buffer connection preset22,5 V
adjustable response value voltage for buffer connection22... 25,5 V; Adjustable in 0,5 V increments
input current at rated input voltage 24 V rated value40 A; + yaklaşık 2,6 A with empty battery
memory
type of energy storagewith batteries
product function DC-UPS modularly expandableVar
design of the mains power cut bridging-connectionDependent on connected battery ve load current, see selection table battery module ve mains buffering times as well as the relevant important information notes!
output
in normal operation at DC rated value24 V
in buffering mode at DC rated value24 V
formula for output voltageVin - yaklaşık 0,5 V
startup delay time typical1 s
voltage increase time of the output voltage typical360 ms
output voltage in buffering mode at DC19... 28,5 V
rated value40 A
in normal operation0... 40 A
in buffering mode0... 40 A
peak current42 A
charging current1 A, 2 A
efficiency
at rated output voltage for rated value of the output current typical97,2 %
in case of operation on rechargeable battery typical96,9 %
at rated output voltage for rated value of the output current typical28,6 W
in case of operation on rechargeable battery typical33,6 W
supplied active power typical960 W
protection and monitoring
reverse polarity protection against energy storage unit polarity reversalVar
reverse polarity protection against input voltage polarity reversalVar
for normal operationNormal operation: LED green (OK), floating changeover contact "Bat/OK" to setting "OK" ("OK" means: Voltage of the supplying power supply unit is greater than cut-in threshold set the DC UPS module); Lack of buffer standby: LED red (alarm), floating changeover contact "Alarm/Bat" to setting "Alarm"; Battery replacement required: LED red (alarm) flashing with yaklaşık 0,25 Hz, floating changeover contact "Alarm/Bat" switching with yaklaşık 0,25 Hz; Energy storage > 85%: LED green (Bat > 85%), floating NOcontact "Bat > 85" closed; Permissible contact current capacity: DC 60 V/1 A veya AC 30 V /1 A
in buffering modeBuffered mode: LED yellow (Bat), floating changeover contact "OK/Bat" to setting "Bat"; Prewarning battery voltage < 20,4 VDC: LED red (alarm), floating changeover contact "Alarm/Bat" to setting "Alarm"; Energy storage > 85%: LED green (Bat > 85%), floating NO contact "Bat > 85" closed
interfaces
product component PC interfaceYok
product function communication functionYok
design of the interfacewithout
safety
galvanic isolation between input and outputYok
operating resource protection classClass III
protection class IPIP20
for emitted interferenceEN 55022 Class B
for interference immunityEN 61000-6-2
standards, specifications, approvals
CE markingVar
UKCA markingVar
MTBF at 40 °C522.739 h
ambient conditions
in horizontal mounting position during operation-25... +70 °C; with natural convection
during transport-40... +85 °C
during storage-40... +85 °C
installation altitude at height above sea level maximum6.000 m
ambient condition relating to ambient temperature - air pressure - installation altitudeIn case of operation altitudes of 2000 - 6000 m above sea level: Output power derating of -7.5 %/1000 m veya reduction of the ambient temperature by 5 K/1000 m
relative humidity with condensation according to IEC 60068-2-38 maximum100 %; RH incl. condensation/frost (no commissioning if condensation is present), yatay installation
chemical resistance to commercially available cooling lubricantsVar; incl. diesel ve oil droplets in the air
resistance to biologically active substances conformity according to EN 60721-3-3Var; Class 3B2 mold, fungal, sponge spores (except fauna); class 3B3 upon request
resistance to chemically active substances conformity according to EN 60721-3-3Var; Class 3C4 (RH < 75%) incl. salt spray acc. to EN 60068-2-52 (severity level 3)
resistance to mechanically active substances conformity according to EN 60721-3-3Var; Class 3S4 incl. sand, dust
resistance to biologically active substances conformity according to EN 60721-3-6Var; Class 6B2 mold, fungal, sponge spores (except fauna)
resistance to chemically active substances conformity according to EN 60721-3-6Var; Class 6C3 (RH < 75%) incl. salt spray acc. to EN 60068-2-52 (severity level 3)
resistance to mechanically active substances conformity according to EN 60721-3-6Var; Class 6S3 incl. sand, dust
coating for equipped printed circuit board according to EN 61086Var; Class 2 for high availability
type of coating protection against pollution according to EN 60664-3Var; Type 1 protection
type of test of the coating according to MIL-I-46058CVar; Discoloration of the coating during service life possible
product conformity of the coating Qualification and Performance of Electrical Insulating Compound for Printed Board Assemblies according to IPC-CC-830AVar; Conformal Coating, Class A
connection method
type of electrical connectionscrew terminal
at input24 V DC: 2 screw terminals for 0,33... 10 mm²/22... 7 AWG
at output24 V DC: 2 screw terminals for 0,33... 10 mm²/22... 7 AWG
for rechargeable battery module24 V DC: 2 screw terminals for 0,33... 10 mm²/22... 7 AWG
for control circuit and status message10 screw terminals for 0,5... 2,5 mm²/20... 13 AWG
mechanical data
width × height × depth of the enclosure102 × 125 × 125 mm
installation width × mounting height102 mm × 225 mm
top50 mm
bottom50 mm
left0 mm
right0 mm
fastening methodSnaps onto DIN rail EN 60715 35x7.5/15
DIN-rail mountingVar
S7 rail mountingYok
wall mountingYok
housing can be lined upVar
net weight1,1 kg
accessories
electrical accessoriesBattery module
additional information
other informationSpecifications rated input voltage ve ambient temperature +25 °C (unless otherwise specified)