Genel bilgiler
Ürün tipi tanımıPS 60 W 120/230 V AC/DC
based on6ES7507-0RA00-0AB0
Mühendislik aracı
STEP 7 TIA Portal configurable/integrated from versionsee entry ID: 109746275
Besleme gerilimi
Nominal değer (DC)120 V / 230 V
İzin verilen aralık, alt sınır (DC)88 V
İzin verilen aralık, üst sınır (DC)300 V
Rated value (AC)120 V / 230 V
permissible range, lower limit (AC)85 V
permissible range, upper limit (AC)264 V
Short-circuit protectionVar
Line frequency
Rated value 50 HzVar
permissible range, lower limit47 Hz
permissible range, upper limit63 Hz
Mains buffering
Mains/voltage failure stored energy time20 ms
Giriş akımı
Rated value at 120 V DC0,6 A
Rated value at 230 V DC0,3 A
Rated value at 120 V AC0,6 A
Rated value at 230 V AC0,34 A
Power
Infeed power to the backplane bus60 W; > +60 °C maks. power input 30 W
Güç kaybı
Power loss at nominal rating conditions12 W
Interrupts/diagnostics/status information
Status indicatorVar
Potential separation
primary/secondaryVar
Isolation
Isolation tested with2.500 V DC/2 s (routine test)
Gerilim darbesine karşı bağışıklık
IEC 61000-4-5’e göre besleme hatlarında girişim bağışıklığıVar; ±1 kV (acc. to IEC 61000-4-5; 1995; surge symm.), ±2 kV (acc. to IEC 61000-4-5; 1995; surge asymm.), no external protective circuit required
Koruma derecesi ve sınıfı
IP koruma sınıfıIP20
Equipment protection classI, with protective conductor
Çalışma ortam sıcaklığı
min.-40 °C; = Tmin (incl. condensation/frost); start-up @ -25 °C
maks.70 °C; = Tmax; for dikey mounting position Tmax = +40 °C
Depolama/taşıma ortam sıcaklığı
min.-40 °C
maks.70 °C
Deniz seviyesine göre çalışma yüksekliği
Installation altitude above sea level, max.2.000 m
Ambient air temperature-barometric pressure-altitudeTmin... Tmax 1.140 hPa... 795 hPa (-1 000 m... +2.000 m)
Bağıl nem
With condensation, tested in accordance with IEC 60068-2-38, max.100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Coolants and lubricants
— Resistant to commercially available coolants and lubricantsVar; Incl. diesel ve oil droplets in the air
Use in stationary industrial systems
— to biologically active substances according to EN 60721-3-3Var; Class 3B2 mold, fungus ve dry rot spores (with the exception of fauna); Class 3B3 talep üzerine
— to chemically active substances according to EN 60721-3-3Var; Class 3C4 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity degree 3); *
— to mechanically active substances according to EN 60721-3-3Var; Class 3S4 incl. sand, dust, *
Use on ships/at sea
— to biologically active substances according to EN 60721-3-6Var; Class 6B2 mold ve fungal spores (excluding fauna); Class 6B3 talep üzerine
— to chemically active substances according to EN 60721-3-6Var; Class 6C3 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity degree 3); *
— to mechanically active substances according to EN 60721-3-6Var; Class 6S3 incl. sand, dust; *
Usage in industrial process technology
— Against chemically active substances acc. to EN 60654-4Var; Class 3 (excluding trichlorethylene)
— Environmental conditions for process, measuring and control systems acc. to ANSI/ISA-71.04Var; Level GX group A/B (excluding trichlorethylene; harmful gas concentrations up to the limits of EN 60721-3-3 class 3C4 permissible); level LC3 (salt spray) ve level LB3 (oil)
Remark
— Note regarding classification of environmental conditions acc. to EN 60721, EN 60654-4 and ANSI/ISA-71.04* The supplied plug covers must remain in place over the unused interfaces during operation!
Conformal coating
Coatings for printed circuit board assemblies acc. to EN 61086Var; Class 2 for high reliability
Protection against fouling acc. to EN 60664-3Var; Type 1 protection
Military testing according to MIL-I-46058C, Amendment 7Var; Discoloration of coating possible during service life
Qualification and Performance of Electrical Insulating Compound for Printed Board Assemblies according to IPC-CC-830AVar; Conformal coating, Class A
Ölçüler
Genişlik70 mm
Yükseklik147 mm
Derinlik129 mm
Ağırlık
Ağırlık, yaklaşık600 g