Genel bilgiler
based on6ES7432-1HF00-0AB0
Yük gerilimi L+
Nominal değer (DC)24 V
Ters polarite korumasıVar
Giriş akımı
from supply and load voltage L+ (without load), max.200 mA; rated load: maks. 400 mA
from backplane bus 5 V DC, max.150 mA
Güç kaybı
Güç kaybı, tipik9 W
Analog çıkışlar
Analog çıkış sayısı8
Voltage output, short-circuit protectionVar
Voltage output, short-circuit current, max.30 mA
Current output, no-load voltage, max.19 V
Output ranges, voltage
0 to 10 VVar
1 V to 5 VVar
-10 V to +10 VVar
Çıkış aralıkları, akım
0 … 20 mAVar
-20 mA to +20 mAVar
4 mA to 20 mAVar
Connection of actuators
for voltage output two-wire connectionVar; possible, without compensation of the line resistances
for voltage output four-wire connectionVar; possible
for current output two-wire connectionVar; possible
Load impedance (in rated range of output)
with voltage outputs, min.1 kΩ
with voltage outputs, capacitive load, max.1 µF
with current outputs, max.500 Ω; 600 ohms if common-mode-voltage reduced to <1 V
Kablo uzunluğu
Ekranlı, maks.200 m
Kanal başına entegrasyon/dönüşüm süresi ve çözünürlük
Aşım dahil çözünürlük (işaret biti dahil), maks.13 bit
Dönüşüm süresi (kanal başına)420 µs; 420 µs in the ranges 1 to 5 V ve 4 to 20 mA; 300 µs in all ranges
Settling time
for resistive load0,1 ms
for capacitive load3,5 ms
for inductive load0,5 ms
Operational error limit in overall temperature range
Voltage, relative to output range, (+/-)0,5 %; ±10 V, 0 to 10 V, 1 to 5 V
Current, relative to output range, (+/-)1 %; ±20 mA, 4 to 20 mV
Basic error limit (operational limit at 25 °C)
Voltage, relative to output range, (+/-)0,5 %; ±10 V, 0 to 10 V, 1 to 5 V
Current, relative to output range, (+/-)0,5 %; ±20 mA, 0 to 20 mA
Interrupts/diagnostics/status information
Diagnostics functionYok
Potential separation analog outputs
Kanallar arasıYok
between the channels and backplane busVar
Isolation
Isolation tested with2.120 V DC between bus ve L+/M; 2.120 V DC between bus ve analog section; 500 V DC between bus ve local ground; 500 V DC between analog section ve L+/M; 2.120 V DC between analog section ve local ground; 2.120 V DC between L+/M ve local ground
Çalışma ortam sıcaklığı
min.0 °C; = Tmin
maks.60 °C; = Tmax
Depolama/taşıma ortam sıcaklığı
min.-40 °C
maks.70 °C
Deniz seviyesine göre çalışma yüksekliği
Installation altitude above sea level, max.5.000 m
Ambient air temperature-barometric pressure-altitudeTmin... Tmax 1.140 hPa... 795 hPa (-1 000 m... +2.000 m) // Tmin... (Tmax - 10 K) 795 hPa... 658 hPa (+2.000 m... +3.500 m) // Tmin... (Tmax -20 K) 658 hPa... 540 hPa (+3.500 m... +5.000 m)
Bağıl nem
With condensation, tested in accordance with IEC 60068-2-38, max.100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Use in stationary industrial systems
— to biologically active substances according to EN 60721-3-3Var; Class 3B2 mold, fungus ve dry rot spores (with the exception of fauna); Class 3B3 talep üzerine
— to chemically active substances according to EN 60721-3-3Var; Class 3C4 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity degree 3); *
— to mechanically active substances according to EN 60721-3-3Var; Class 3S4 incl. sand, dust, *
Use on ships/at sea
— to biologically active substances according to EN 60721-3-6Var; Class 6B2 mold ve fungal spores (excluding fauna); Class 6B3 talep üzerine
— to chemically active substances according to EN 60721-3-6Var; Class 6C3 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity degree 3); *
— to mechanically active substances according to EN 60721-3-6Var; Class 6S3 incl. sand, dust; *
Usage in industrial process technology
— Against chemically active substances acc. to EN 60654-4Var; Class 3 (excluding trichlorethylene)
— Environmental conditions for process, measuring and control systems acc. to ANSI/ISA-71.04Var; Level GX group A/B (excluding trichlorethylene; harmful gas concentrations up to the limits of EN 60721-3-3 class 3C4 permissible); level LC3 (salt spray) ve level LB3 (oil)
Remark
— Note regarding classification of environmental conditions acc. to EN 60721, EN 60654-4 and ANSI/ISA-71.04* The supplied plug covers must remain in place over the unused interfaces during operation!
Conformal coating
Coatings for printed circuit board assemblies acc. to EN 61086Var; Class 2 for high reliability
Protection against fouling acc. to EN 60664-3Var; Type 1 protection
Military testing according to MIL-I-46058C, Amendment 7Var; Discoloration of coating possible during service life
Qualification and Performance of Electrical Insulating Compound for Printed Board Assemblies according to IPC-CC-830AVar; Conformal coating, Class A
Ölçüler
Genişlik25 mm
Yükseklik290 mm
Derinlik210 mm
Ağırlık
Ağırlık, yaklaşık650 g