Genel bilgiler
product brand nameSIPLUS
product type designationPM 1207
product designationS7-1200 Power Module
type of current supply24 V/2,5 A
manufacturer's article number of the basic version used for SIPLUS product versions6EP1332-1SH71
input
type of the power supply network1-phase AC
phase number1
voltage curve at inputAC
supply voltage at ACAutomatic range selection
supply voltage120 V/230 V
input voltage 1 at AC85... 132 V
input voltage 2 at AC176... 264 V
at 50 Hz230 V
at 60 Hz120 V
line frequency50/60 Hz
line frequency47... 63 Hz
wide range inputYok
overvoltage overload capability2,3 × Vin rated, 1,3 ms
buffering time for rated value of the output current in the event of power failure minimum20 ms
operating condition of the mains bufferingVin = 93/187 V
at rated input voltage 120 V1,2 A
at rated input voltage 230 V0,67 A
current limitation of inrush current at 25 °C maximum13 A
maximum3 ms
I2t value maximum0,5 A²·s
fuse protection typeT 3,15 A/250 V (not accessible)
fuse protection type in the feederRecommended miniature circuit breaker: 16 A characteristic B veya 10 A characteristic C
output
voltage curve at outputControlled, isolated DC voltage
product function output voltage controlledVar
product function output voltage stabilizedVar
output voltage at DC rated value24 V
at output 1 at DC rated value24 V
at output 1 at DC24 V
output voltage adjustableYok; -
relative overall tolerance of the voltage3 %
on slow fluctuation of input voltage0,1 %
on slow fluctuation of ohm loading0,2 %
maximum150 mV
maximum240 mV
display version for normal operationGreen LED for 24 V OK
behavior of the output voltage when switching onYok overshoot of Vout (soft start)
response delay maximum6 s; 2 s 230 V, 6 s 120 V
typical10 ms
rated value2,5 A
rated range0... 2,5 A
supplied active power typical60 W
on short-circuiting during the start-up typical6 A
at short-circuit during operation typical6 A
on short-circuiting during the start-up100 ms
at short-circuit during operation100 ms
bridging of equipmentVar
number of parallel-switched equipment resources for increasing the power2
efficiency
efficiency in percent83 %
at rated output voltage for rated value of the output current typical12 W
closed-loop control
relative control precision of the output voltage with rapid fluctuation of the input voltage by +/- 15% typical0,3 %
relative control precision of the output voltage load step of resistive load 50/100/50 % typical3 %
load step 50 to 100% typical5 ms
load step 100 to 50% typical5 ms
maximum5 ms
protection and monitoring
design of the overvoltage protection< 33 V
property of the output short-circuit proofVar
design of short-circuit protectionConstant current characteristic
typical2,65 A
typical2,7 A
safety
galvanic isolation between input and outputVar
galvanic isolationOutput voltage: SELV, ES1 (IEC 62368-1), DVC As (IEC 61204-7)
operating resource protection classClass I
maximum3,5 mA
protection class IPIP20
EMC
for emitted interferenceEN 55022 Class B
for mains harmonics limitationnot applicable
for interference immunityEN 61000-6-2
standards, specifications, approvals
CE markingVar
UKCA markingVar
MTBF at 40 °C1.492.537 h
ambient conditions
in horizontal mounting position during operation-25... +70 °C; with natural convection
during transport-40... +85 °C
during storage-40... +85 °C
installation altitude at height above sea level maximum6.000 m
ambient condition relating to ambient temperature - air pressure - installation altitudeIn case of operation altitudes of 2000 - 6000 m above sea level: Output power derating of -7.5 %/1000 m veya reduction of the ambient temperature by 5 K/1000 m
relative humidity with condensation according to IEC 60068-2-38 maximum100 %; RH incl. condensation/frost (no commissioning if condensation is present), yatay installation
chemical resistance to commercially available cooling lubricantsVar; incl. diesel ve oil droplets in the air
resistance to biologically active substances conformity according to EN 60721-3-3Var; Class 3B2 mold, fungal, sponge spores (except fauna); class 3B3 upon request
resistance to chemically active substances conformity according to EN 60721-3-3Var; Class 3C4 (RH < 75%) incl. salt spray acc. to EN 60068-2-52 (severity level 3)
resistance to mechanically active substances conformity according to EN 60721-3-3Var; Class 3S4 incl. sand, dust
resistance to biologically active substances conformity according to EN 60721-3-6Var; Class 6B2 mold, fungal, sponge spores (except fauna)
resistance to chemically active substances conformity according to EN 60721-3-6Var; Class 6C3 (RH < 75%) incl. salt spray acc. to EN 60068-2-52 (severity level 3)
resistance to mechanically active substances conformity according to EN 60721-3-6Var; Class 6S3 incl. sand, dust
coating for equipped printed circuit board according to EN 61086Var; Class 2 for high availability
type of coating protection against pollution according to EN 60664-3Var; Type 1 protection
type of test of the coating according to MIL-I-46058CVar; Discoloration of the coating during service life possible
product conformity of the coating Qualification and Performance of Electrical Insulating Compound for Printed Board Assemblies according to IPC-CC-830AVar; Conformal Coating, Class A
connection method
type of electrical connectionscrew terminal
at inputL, N, PE: 1 screw terminal her biri for 0,5... 2,5 mm²
at outputL+, M: 2 screw terminals her biri for 0,5... 2,5 mm²
for auxiliary contacts-
mechanical data
width × height × depth of the enclosure70 × 100 × 75 mm
installation width × mounting height70 mm × 140 mm
top20 mm
bottom20 mm
left0 mm
right0 mm
fastening methodSnaps onto DIN rail EN 60715 35x7.5/15, wall mounting
DIN-rail mountingVar
S7 rail mountingYok
wall mountingVar
housing can be lined upVar
net weight0,3 kg
additional information
other informationSpecifications rated input voltage ve ambient temperature +25 °C (unless otherwise specified)