Photo may not represent actual item. Refer to name and product specs for all details.
Char-Lynn (Danfoss) 105-1171-006 Disc Valve Motors
Hydraulic Geroler Disc Valve Motor - 2000 - Wheel, 306.6 cm³/r Max Geometric Displacement
ITEM #6904fbb8db5b3f8c5929cb91 MFR #105-1171-006 SKU #YLSPEVSE5Q8X3IV
المواصفات السريعة
Series: 2000 - Wheel
Displacement: 18.71 in³/r
Shaft Type: Taper
Max Operating Temperature: 180 °F
Output Shaft Size: 1-1/4 in Tapered - Threaded End
Overall Height: 5.28 in
نظرة عامة
Hydraulic Geroler Disc Valve Motor - 2000 - Wheel, 306.6 cm³/r Max Geometric Displacement
الميزات والفوائد
- Lowest pressure drop motor in the industry|Highly-efficient Geroler motor provides energy savings
المواصفات الفنية
Series 2000 - Wheel
Displacement 18.71 in³/r
Shaft Type Taper
Max Operating Temperature 180 °F
Output Shaft Size 1-1/4 in Tapered - Threaded End
Overall Height 5.28 in
Overall Length 8.47 in
Overall Width 5.28 in
Seal Type Viton Shaft Seals
Drain Connection Size .4375-20 Unf-2b O-ring Port Size -4
Operation Rating Description Continuous Rating - Motor May Be Run Continuously At These Ratings. / Intermittent Operation - 10 Percent Of Every Minute / Peak Operation - 1 Percent Of Every Minute
Mounting Type 4-Bolt Flange - 4.25 in Pilot
Port Orientation Staggered Ports
Replacement Balance Ring 006 Design - 8915-000 - 1 Required
Replacement Buna Seal Kit 006 Design - 61258-000 - 1 Required
Replacement Drive - Sold Separately 006 Design - 21371-007 - 1 Required
Replacement Drive Valve 006 Design - 8433-000 - 1 Required
Replacement Geroler - Sold Separately 006 Design - 21625-007 - 1 Required
Replacement Housing Bearing Side Fnt 006 Design - 21578-003 - 1 Required
Replacement Long Cap Screw Cap End 006 Design - 14384-012 - 4 Required
Rplc Output Shaft And Bearing Kit 006 Design - 21618-003 - 1 Required
Replacement Pin For Balance Ring 006 Design - 14351-000 - 2 Required
Replacement Plate Valve 006 Design - 22134-000 - 1 Required
Replacement Rear Housing 006 Design - 21564-001 - 1 Required
Replacement Valve Sold Separately 006 Design - 21466-000 - 1 Required
Replacement Viton Seal Kit 006 Design - 61263-000 - 1 Required
Replacement Wear Place 006 Design - 22102-000 - 1 Required
Replacement Pin For Balancing Ring 006 Design - 14351-000 - 2 Required
Actual Mounting Flange 4-Bolt Flange - Wheel - With 4-1/4 In. Pilot Dia.
Actual Output Shaft Taper
Actual Port Type .875-14 UNF-2B SAE O-Ring Ports - Staggered Ports, Motor To Fit Within 127.0 [5.00] Dia. Tube
Continuous Flow Rate 75 L/min
Intermittent Pressure 240 bar
Max Continuous Oil Viscosity 70 Saybold universal second
Maximum RPM-Continuous 246 rpm
Port Configuration .875-14 UNF-2B SAE O-Ring Ports - Staggered Ports, Motor To Fit Within 127.0 [5.00] Dia. Tube
منتجات مميزة
منتجات اخترناها لك